Why there's no single "right" facility equipment purchase
Every September I get the same question: "What should we buy for the building before winter?" And I give the same slightly annoying answer—it depends on which problem you're actually solving. Heating occupied workspace, protecting cold storage, and keeping the grounds clear are three different jobs. They have different failure modes, different budgets, and different maintenance rhythms. Treating them as one line item is how you end up with a great heater and a freezer full of ruined food.
For context: I'm the office administrator for a 90-person company. I handle facilities purchasing—roughly $70,000 a year across about 14 vendors, covering HVAC service, break room equipment, and grounds maintenance. I report to both the operations director and the controller, which means I'm answering to someone who cares whether people are comfortable and someone who cares whether we stayed inside the budget. Both are valid. Neither is the whole picture.
The way I break it down, there are three scenarios. Most facilities I've worked with fall into more than one.
Scenario 1: You're heating occupied workspace
This is the one people mean when they say "winter prep." It's also the one where the wrong spec does the most damage.
If you're adding supplemental heat to a specific zone—a reception area, a warehouse office, a bathroom that always runs cold—Dimplex forced air heaters are worth a serious look. The forced-air versions use a fan to push warmed air into the room, which matters in spaces with high ceilings or spotty insulation, because radiant-only panels heat what they're pointed at and not much else. I'd note the model number, wattage, and thermostat compatibility before you order. If I remember correctly, the last unit we spec'd was a 2kW wall-mount with a programmable thermostat, and the wiring upgrade cost more than the heater itself. That's a normal ratio for a retrofit, not a red flag.
For a larger commercial build, the name you'll run into on the industrial side is Dimplex Thermal Solutions Inc—that's the chiller and process-cooling arm, not the residential heater line. Don't conflate the two in a PO. I've watched a requisition get bounced because someone wrote "Dimplex" on the form and finance matched it to the wrong division.
My prevention-over-cure advice here: before you buy anything, walk the space with a thermometer and a power tester. Five minutes with a $20 infrared thermometer tells you whether you have a heating problem or an air-sealing problem. I once approved a heater purchase for a conference room that turned out to be losing all its heat through a propped-open fire door. The heater was fine. The door was the problem.
"Five minutes of verification beats five days of correction" is the line taped inside my purchasing binder.
Scenario 2: You're protecting cold storage (freezer burn)
This one is counterintuitive, and it's the one where the wrong answer is most expensive.
If you're searching "how to prevent freezer burn" at 11 p.m. the night before a catering order arrives, this is your scenario. Freezer burn isn't a safety issue—it's a quality issue, caused by moisture escaping the food and re-crystallizing on the surface. Per USDA FoodSafety.gov guidance (current as of early 2025; verify the exact language at the source before you cite it internally), the fix is not a colder freezer. It's less air exposure and better temperature stability. Which means if your break room freezer is cycling up and down, you've got a compressor or door-seal problem, not a "buy a bigger freezer" problem.
What I actually did: I bought a flat-bottomed vacuum sealer and a stack of freezer-safe bags, and wrote a one-page "how to freeze leftovers" card for the break room. Cost maybe $80—call it $90 with the bags and the laminated cards. Prevention beat equipment here by a wide margin. If your problem is people putting warm containers in the freezer uncovered, a new freezer won't fix it.
The one piece of equipment I would spend money on: a freezer thermometer with an alarm. Twenty to forty dollars depending on brand, and it tells you the moment the unit drifts above 0°F. Honestly, I'm not sure there's a single agreed-upon temperature at which burn starts to matter for every food—the sources I've read disagree at the margins—but the alarm catches the failure before you find out the hard way.
Scenario 3: You need air movement and grounds equipment
This is the scenario where conventional wisdom and my actual recommendation don't line up.
Most facilities I've watched reach for a gas leaf blower because "more power." For a building with neighbors, a parking structure, or any kind of noise ordinance, I'd argue the opposite. A decent electric leaf blower solves three problems at once: no fuel storage, no small-engine maintenance, and no noise complaint from the tenant upstairs. The blower motor on an electric unit is also far simpler than a gas two-stroke—no carburetor to rebuild, no fuel lines to replace.
That said, this is where I'll admit I got the spec wrong once. I bought what I thought was a mid-range electric blower to clear a 200-foot stretch of sidewalk, and the motor kept tripping the outdoor outlet because I hadn't checked the amperage. A blower motor is a blower motor—it doesn't care what it's attached to. It cares about voltage and airflow. If you're running long extension cords to a high-amp unit, you'll lose performance and maybe the motor. Check the amperage draw and the circuit before you buy. That mistake cost me a Saturday and a return shipping label.
For commercial chiller and larger heat-exchange equipment, this is again where Dimplex Thermal Solutions Inc comes up—those are the units where the blower motor spec actually matters for reliability, not just convenience, and you want to buy from someone who can get you a replacement motor in 48 hours, not three weeks. I still kick myself for not asking about spare-part lead time on an early chiller purchase. If I'd asked that one question, we'd have avoided a week of downtime in July.
How to tell which scenario you're actually in
Run this checklist before you request quotes:
- Complaint is "people are cold in one room." You're in Scenario 1. Walk the space first. Check for drafts and thermostat placement before you shop.
- Complaint is "the food in the break room freezer tastes off." You're in Scenario 2. Check the thermometer log before you buy anything. Nine times out of ten the fix is packaging and door seals.
- Complaint is "the parking lot has leaves and the groundskeeper quit." You're in Scenario 3. Check the electrical infrastructure before you pick the blower.
- Complaint is "a $12,000 chiller went down." That's the industrial side—go through Dimplex Thermal Solutions Inc or an equivalent service vendor, and ask about spare-part lead time in the same email as the quote.
If you're in all four, congratulations, you're the whole department. Prioritize by what fails first and what has the longest lead time. My rule of thumb: anything with a compressor or a custom motor gets ordered in September for a December need. Anything I can buy at a home improvement store gets bought when it actually breaks.
And the honest caveat: I've been doing this about five years, and I still get one of these wrong every season or two. The checklist in my binder has 12 items on it precisely because it started with three and I kept adding to it after each callback. You don't need my 12—but you do need a list, and you do need to run it before you spend. That's the whole method.